The C&C Auto Show – C & C Automotive Blog

With the recent focus in Evans on improving fuel economy, we’ve been told how important it is to maintain our tire pressure.

Everyone in Evans knows that tires wear out, but we all want to make them last as long as possible because they’re fairly expensive to replace. In addition to saving gas, properly inflated tires last longer. Under-inflated tires will wear out more quickly.

Some people in Evans wonder if there is benefit to adding a few extra pounds of pressure when they fill up their tires. But actually, there isn’t. In fact, there are very good reasons not to over-inflate your tires. For one, the middle of the tread will wear unevenly because the full tread is not contacting the road properly. That also adversely affects your handling.

Come in and see us about tire maintenance for your Augusta, Georgia vehicle.
C & C Automotive
990 Telfair Street
Augusta, Georgia 30901
706-724-0900

Every vehicle in the Evans area has a sticker on the driver’s side door jamb that tells you the manufacturer’s recommended tire pressure. This recommendation is an integral part of the vehicle’s suspension tuning. A lot of engineering actually goes into the recommended tire pressure, so it’s important to follow it.

What else do we need to know about tire maintenance? Tire rotation and balancing are very important. Let’s start with rotation. Because the front tires handle the brunt of turning forces, the shoulders of the front tires wear more quickly than the rear tires. We rotate the tires so that they all get to do some duty on the front and they’ll all wear evenly over their life.

For most vehicles, front tires are rotated to the rear and vice versa. Others recommend a cross rotational pattern. Some vehicles use an asymmetrical tire so those tires need to stay on either the right or left side – it’ll say which on the tire. Some high performance cars have asymmetrical tires and different sizes on the front and rear. These can’t be rotated at all. Your owner’s manual will have details for your car.

How often should you rotate your tires? Your owner’s manual will have a recommendation. Your service advisor at C & C Automotive can do a visual inspection to let you know if it looks like it should be done. The interval is typically around 5,000 miles.

You know, some people don’t think new tires need to be balanced. What they aren’t taking into account is the wheel. Between the wheel and the tire – even a new tire – there’s enough variation to require balancing.

When you add the valve stem and tire pressure monitoring sensors required on new cars, balancing is definitely in order. When a tire’s out of balance, it’s actually hopping down the road. You’ll feel the vibration through the steering wheel if a front tire’s out of balance and through your seat if it’s a rear tire.

Proper wheel balance promotes tire life and increases safety. Historically, lead weights have been attached to the wheel to bring it into balance. Lead gives some environmental concern, so steel weights are starting to be substituted.

Also, always use the same size tire on an axle. Different size tires on the front or on the back can lead to some real handling problems. And tire manufacturers recommend that when you get two new tires, they be installed on the rear because that’s where you need the most traction to avoid spinning-out.

Hey Augusta, are your tires worn out? What is the standard for our Georgia streets? How can you tell on your SUV?

While there may be legal requirements for the Augusta area, there are safety concerns that go beyond meeting minimum replacement mandates.

2/32 is the depth of the tire tread wear indicator bars that US law has required to be molded across all tires since August 1, 1968. When tires are worn so that this bar is visible, there’s just 2/32 of an inch – 1.6 millimeters – of tread left. It’s that level of wear that’s been called into question recently.

We’re referring to the Consumer Reports call to consider replacing tires when tread reaches 4/32 of an inch, or 3.2 millimeters. And the recommendation is backed by some very compelling studies.

The issue is braking on wet surfaces in and around Augusta. Most of us think of our brakes doing most of the work, but if you don’t have enough tread on your tires, the brakes can’t do their job. When it’s wet or snowy, the tread of the tire is even more critical to stopping power.

Picture this: you’re driving over a water covered stretch of road near Augusta, Georgia. Your tires must be in contact with the road in order to stop. That means that the tire has to move the water away from the tire so that the tire is actually contacting the road and not floating on a thin film of water.

Floating on the surface of water is called hydroplaning. So if there’s not enough tread depth on a tire, it can’t move the water out of the way and you start to hydroplane.

In the study a section of a test track was flooded with a thin layer of water. If you laid a dime on the track, the water would be deep enough to surround the coin, but not enough to cover it.

A car and a full-sized pick-up were brought up to 70 miles per hour, or 112 kilometers an hour and then made a hard stop in the wet test area. Stopping distance and time were measured for three different tire depths:

• New tire tread depth
• 4/32 of an inch
• 2/32 of an inch

So what happened with the 2/32 tires on the car? Get this – when the car had traveled the distance required to stop with new tires, it was still going 55 miles an hour. Stopping distance was nearly doubled to 379 feet and it took 5.9 seconds.

Wow! That means if you barely have room to stop with new tires, you would hit the car in front of you at 55 miles an hour with the worn tires.

Now, with the partially worn tires – at 4/32 of an inch – the car was still going at 45 miles an hour at the point where new tires brought the car to a halt. It took nearly 100 feet more room to stop and 1.2 seconds longer. That’s a big improvement. We can see why Consumer Reports and others are calling for a new standard.

Of course, stopping distances were greater for the heavier pick-up truck.

How do you know when your tires are at 4/32 of an inch? Easy; just insert a quarter into the tread. Put it in upside down. If the tread doesn’t cover George Washington’s hairline, it’s time to replace your tires. With a Canadian quarter, the tread should cover the numbers in the year stamp.

You may remember doing that with pennies. A penny gives you 2/32 to Abraham Lincoln’s head. The quarter is the new recommendation – 4/32.

How do people feel about replacing their tires earlier? Well, tires are a big ticket item and most people want to get the most wear out of them that they can. But do you want that much more risk just to run your tires until they are legally worn out?

For us, and we would guess for many, the answer is “no”.

C & C Automotive
990 Telfair Street
Augusta, Georgia 30901
706-724-0900

With the recent focus in Evans on improving fuel economy, we’ve been told how important it is to maintain our tire pressure.

Everyone in Evans knows that tires wear out, but we all want to make them last as long as possible because they’re fairly expensive to replace. In addition to saving gas, properly inflated tires last longer. Under-inflated tires will wear out more quickly.

Some people in Evans wonder if there is benefit to adding a few extra pounds of pressure when they fill up their tires. But actually, there isn’t. In fact, there are very good reasons not to over-inflate your tires. For one, the middle of the tread will wear unevenly because the full tread is not contacting the road properly. That also adversely affects your handling.

Come in and see us about tire maintenance for your Augusta, Georgia vehicle.
C & C Automotive
990 Telfair Street
Augusta, Georgia 30901
706-724-0900

Every vehicle in the Evans area has a sticker on the driver’s side door jamb that tells you the manufacturer’s recommended tire pressure. This recommendation is an integral part of the vehicle’s suspension tuning. A lot of engineering actually goes into the recommended tire pressure, so it’s important to follow it.

What else do we need to know about tire maintenance? Tire rotation and balancing are very important. Let’s start with rotation. Because the front tires handle the brunt of turning forces, the shoulders of the front tires wear more quickly than the rear tires. We rotate the tires so that they all get to do some duty on the front and they’ll all wear evenly over their life.

For most vehicles, front tires are rotated to the rear and vice versa. Others recommend a cross rotational pattern. Some vehicles use an asymmetrical tire so those tires need to stay on either the right or left side – it’ll say which on the tire. Some high performance cars have asymmetrical tires and different sizes on the front and rear. These can’t be rotated at all. Your owner’s manual will have details for your car.

How often should you rotate your tires? Your owner’s manual will have a recommendation. Your service advisor at C & C Automotive can do a visual inspection to let you know if it looks like it should be done. The interval is typically around 5,000 miles.

You know, some people don’t think new tires need to be balanced. What they aren’t taking into account is the wheel. Between the wheel and the tire – even a new tire – there’s enough variation to require balancing.

When you add the valve stem and tire pressure monitoring sensors required on new cars, balancing is definitely in order. When a tire’s out of balance, it’s actually hopping down the road. You’ll feel the vibration through the steering wheel if a front tire’s out of balance and through your seat if it’s a rear tire.

Proper wheel balance promotes tire life and increases safety. Historically, lead weights have been attached to the wheel to bring it into balance. Lead gives some environmental concern, so steel weights are starting to be substituted.

Also, always use the same size tire on an axle. Different size tires on the front or on the back can lead to some real handling problems. And tire manufacturers recommend that when you get two new tires, they be installed on the rear because that’s where you need the most traction to avoid spinning-out.